Tag Archives: repair

What am I up this week? 4-5-12

Nothing. What I am considering is that I have a lot to accomplish, but since I graduated from college I’ve never felt busier. Perhaps it’s because I took on Amateur Radio and that gets a little attention here and there.

Usually, I am the one that does the repairing on musical equipment, but this week Continue reading

Repairing an Organ: Holiday with Genie does not power up

Holiday with Genie organ

Holiday with Genie organ

I had a recent repair job that I thought was hopeless. I’m not a fan of a million wires, and when I heard about this repair, I knew that if nobody else wanted to repair it, I was going to be challenged.

Well, I accepted the challenge. I went to the owner’s house and began disassembling the organ to gain access to the inside. I found gaining access to be easy, but I was instantly overwhelmed by the number of wire wrapped connections inside. This was a very complex design.

I flipped on the power switch, and I noticed that the baffle around one of the speakers spun a little, so I knew something was working. I tried everything to make some noise, but nothing happened other than making the speaker baffle spin faster. Continue reading

Another broken USB drive has been salvaged…long enough to extract the data.

The word got out that I was able to piece USB drives back together.  This one was a no-namer 1GB drive, and it was thrashed!!! It is missing a resistor and a capacitor. I sure had one heck of a time making the connections, too. One of the data pins had a persistent solder bridge to ground, and I finally whipped out a thin kitchen knife to scrape the bridge away. Then I broke the data pin from the circuit board, bent it up, and made an “air” connection to avoid another bridge. I hate solder bridges on SMT devices. They are just shy from being impossible to get rid of.
Continue reading

This week @ Tech-tut (August 13, 2010)

There’s not a lot going on this week. I’m finishing up the second tube amp build. This evening, and probably at lunch, too, I’m going to finish the V1.3 changes. I intermittently changed some things that were not noted in the schematics prior to V1.3, and I need to change them back. I am going to make a video or two to post to Youtube to demonstrate the amp. Nothing beats seeing. Seeing is believing. I want to install a switch to change from pentode to triode mode like the AX84 project did, but I’m still debating whether or not it’s worth doing. I’ll probably do it, and if it doesn’t sound different, I’ll just be stuck with it.

I also had to add a DC cooling fan to blow in the cabinet because the LM317 cases get fiery hot. The temperature of the heat sink was over 180° F after an hour of playing. The chassis was around 150° F. That’s just too hot. The EL84 runs at about 350° F, but I’m pretty sure that temperature is acceptable for a power tube. I suspended a fan to blow on the heat sink to see how much noise it imposes on the amp, and there is none. I also checked to see how direct the air needs to be to keep it under 125° F. Direct it stays under 100° F, but I’d wind up sticking my hand in the fan every time I went to turn it off. I made a makeshift bracket from a scrap piece of 1/8″ aluminum sheet. I put a piece of vinyl to keep the fan from rattling on the bracket. A picture of this is certainly worth a thousand words.

BTW…I played the amp this morning at 7, and it sounds much better now that I changed the first preamp stage’s cathode bypass resistor to 2.7k. :) This makes me happy.

I spoke with Grayson Sigler about the micRo CNC router delivery, and they were running a little behind due to a family illness. I expect within another week or so I’ll be pulling hair out learning a new skill. I’m glad that Grayson and Lumenlab are happy to help. I have also sought help from Pcb-gcode.org and probably others. I want to gain as much knowledge and experience so I may also be of help in the future. You can expect that the CNC routing experiences will be heavily blogged and video logged.

Other than waiting for amp parts to arrive, everything is calm on the tech front.

“It’s more than just a project.”